80A 12V/24V Solar PV Cell Battery Charge Controller 80I
- Minimal order
- 100 pieces
Message Phone call
Product Specifications
Model Number
80I
Product Description
80A 12V/24V Solar Charger Discharger Controller with LED Indicator Battery Charging Status 80I
20I-20A / 30I-30A / 60I-60A / 80I-80A
Specification
Model | 80I |
Rated Current | 80A |
Rated Voltage | 12V/24V |
Maximum Voltage of solar panel | 50V |
Float Voltage | 13.7V/27.4V |
Low Voltage Disconnection | 10.7V/21.4V |
Low Voltage Reconnection | 12.6V/25.2V |
No load loss | <30mA |
loop voltage drop | <200mV |
Charging Mode | PMW Mode |
Temperature Compensation | -4mV/Cell/ °C |
Installtion cable area | >3# AWG ( 25mm2 ) |
Operation temperature | -20 °C ~ 50 °C |
storage temperature | -30 °C ~ 70 °C |
Humidity requirement | <90% , no condensation |
Size | 130mm*188mm*62mm |
Mounting hole spacing | 90 mm 178 mm -- 5 |
Weight | 700g |
Main Features
Application Method
Solar Home System Solar Street Light System
System | 12V | 24V |
Max PV Input Power | 960W | 1920W |
Max PV Input Voltage | 18V | 36V |
Battery Voltage | 12V | 24V |
Load Output Current | 80A | 80A |
Attention
Connection Order:
Connect the battery with the controller.
Connect the solar panel with the controller.
Connect the load with the controller or inverter.
Disconnection order:
Disconnect the solar panel.
Disconnect the battery.
Disconnect the load.
Precautions:
please make sure connect your inverter with your battery
Please avoid to install in the following environments wet,dusty places or places with flammable and explosive gases.
Install the controller at the vertical plane.
Instructions80A 12V Solar Controller 24V panel Battery Charge Controller Solar Home system indoor use LCD 60 Amps Solar Charge Controller
keywords: 80a solar charge controller,solar charge controller 80 amps,solar regulator
Package including:
1. 1pcs 80a solar controller
2. 1pcs temp sensor
3. 1pcs user manual
Solar panel power: 720W/12V 1440W/24V
Installation
1. Ready tools and cables. Encourage you to matching the right cables. Ensure that the current density<4mm2 that is conductive to reducing the line voltage drop. Recommended: 60A with 20mm2 cable. Check weather the installation sitescompliance with the relevant safety requirements. Please avoid the damp, dusty, there is a place flammable, explosive and corrosive gases use the controller to install.
2. Install the controller into a fixed vertical plane. See section 5 of the pore size and pore spacing. In order to ensure a good thermal control conditions, please set aside each 10cm below the controller space.
3. As shown on the right, connect the (1) Load, (2) Battery and (3) Solar Panel to the controller according to the order of (1) (2) (3). Pay attention to the load, battery, solar panel and controller of same polarity.
4. Put into the external temperature sensor on the left of the controller (probe port). The temperature sensor should be similar space with battery. (Otherwise, the controller will control the parameters of all wrong temperature compensation.)
5.If you have remote monitoring and control function, please insert one end of the included communication wire on the right of the controller (communication port), the other end to connect to The host computer.
Demolition: To prevent accidents, please order the demolition of solar panels, battery and load disconnect with controller.
Note:Battery polarity will not damage the controller, but you will have a load equipment security risks
Data Sheet
Model | 80I |
|
Rated Current | 80A |
|
Rated Voltage | 12V/24V | |
Maximum Voltage of solar panel | 50V | |
Float Voltage | 13.7V/27.4V | |
Low Voltage Disconnection | 10.7V/21.4V | |
Low Voltage Reconnection | 12.6V/25.2V | |
No load loss | <30mA | |
loop voltage drop | <200mV | |
Charging Mode | PMW Mode | |
Temperature Compensation | -4mV/Cell/ °C |
Supply Ability
--
Packaging and Shipping
Lead time
--
Port
--
Packaging details
--